CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY, DO NOT EXPOSE TO RAIN, STORE INDOORS.

为了避免触电伤害，不要将产品暴露在雨里，需室内储藏。

The substances used with this spray applicator (paint, thinners etc) may contain hazardous, harmful, explosive or corrosive materials.

喷枪所喷物质（油漆，稀释剂等）可能含有危险的，有害的或者易爆，腐蚀性特质。

ALWAYS COMPLY WITH THE SAFETY INSTRUCTIONS ISSUED WITH THIS PRODUCT AND THE MATERIAL BEING USED.

工作时，请按安全使用说明操作。

?The spray applicator must only be used with paints and solvents that have a suitable flash point for spraying. If in doubt, consult the paint or solvent manufacturer’s data

喷枪设备只能使用涂料及稀释剂等适合喷涂的液体， 如有疑问， 请查阅“疑问及解决方法”部分

?Always ensure there is adequate ventilation when spraying.

请在通风的环境下工作。

?NEVERspray near an open flame, including an appliance pilot flame.

不要对着火源。

?NEVERsmoke when spraying.

工作时，请不要抽烟

?Always disconnect the unit from the mains supply when cleaning the spray applicator.

清洗设备时，请将各部分分开。

?Always ensure the spray area is safe and free from all debris that may present a fire or trip hazard.

请确保喷涂区域是安全的，远离可能带来危险的因素。

?NEVER, under any circumstances, point the spray gun at another person or animal. In the event of injury occurring, seek expert medical advice immediately.

无论在什么情况下，喷嘴不要对着人和动物，以免带来伤害。如果伤害发生，请立即就医。

?NEVERallow children or unauthorized users to operate or play with the spray equipment. This equipment is for professional use only.

不要让孩子或未经许可的人操作或者玩弄喷枪设备。此设备仅给专业人士使用。

?Always read the paint manufacturer’s thinning instructions before use.

使用前， 请阅读稀?退得鳌?

?Always wear the correct protective face mask when spraying. We also recommend wearing gloves, goggles and overalls.

工作时请戴防护面罩。我们建议戴手套，眼镜，穿工作服。

?After every use ensure that you clean the spray gun thoroughly & grease the gland washer.

请确认每使用后，全面清洗喷枪和吸料管

?Use only genuine manufacturer replacement parts.

仅使用生产厂家的配件

?Only use the spray equipment as detailed in these instructions.

 ?Do not use the air hose or mains cable to pull the HVLP unit.

不要用送气管或者电线拉动整?錾璞浮?

?Check the hoses, hose connectors and mains cable daily. Any worn or damaged parts should be replaced immediately.

请检查送气管， 送气管连接件及电线。 一旦有损坏， 需及时更换。

?This appliance is recommended for household use only.

此设备建议家庭使用。

?This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

产品不适合生病，感知障碍，或者缺乏经验知识的人（包括孩子）使用，除非他们在有行为能力的人的监督或者指导下使用。

 IMPORTANT ELECTRICAL INFORMATION重要电路知识

 EXTENSION CORDS

延长电线

Your JML HVLP is supplied with a power cord that is 6 feet long. Make sure your extension cord is in good condition.您所使用的电线长度为1.5M，如需延长，请确认你的电线板状况良好。

When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. For lengths between 0 feet and 50 feet, No 18 AWG extension cords should be used.

当使用延长电路时，请确认使用的是一个能够承载喷枪?璞傅目梢酝隙牡缏钒濉Ｔ?0~15M之间的距离， 可以使用18 AWG延长电路。

 DOUBLE INSULATED APPLIANCE双绝缘设备

This is a double insulated appliance and as such, does not require three-way grounding. This product is equipped with a polarized alternating current line plug (a plug having one blade wider than the other) and does not require a grounding adapter. This plug will fit into the power outlet only one way. This is a safety feature.

If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact a qualified electrician to replace the obsolete outlet. Do not defeat the safety purpose of the polarized plug.

此产品是双绝缘产品，不需要三线配电系统。产品配备是使用两个头的插头（两个头的插头中一个比另一个宽），不需要接地插头。如果你不能把插头?迦氩蹇桌铮髡幌虏逋贰?插头仍不能插入，可请咨询专业电工。

CAUSE PREMATURE WEAR, WHICH WILL VOID THE GUARANTEE. TO OBTAIN THE BEST RESULTS FROM YOUR SPRAY KIT PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE USE.

本品不适用于质地粗糙的涂料，使用这些材料会对产品造成永久性损坏，影响保修，为更好地使用本产品，请阅读以下说明书

IDEAL VISCOSITY理想粘度

Water based paints and emulsions：25-50 seconds水基油漆和乳化液   25-50秒                     

Varnishes：No Dilution油漆    不需要稀释。

Aluminium PaintsNo Dilution铝油漆：不需要稀释

Oil Based Paints45 -50 seconds油基漆：45-50秒

Wood Stains： No Dilution 木漆 不需要稀释

Wood preservatives  No Dilution        木材防腐剂 不需要稀释

Automotive Paint：Manufacturers Ratio 自喷漆： 生产厂家出厂时的比例

Primers45 -50 seconds：底漆：45-50秒

This spray gun can be used with products having a viscosity ranging from 25 to a maximum of 50 seconds. Dip the viscosity cup into the material and fill up. Time how long it takes for the viscosity cup to empty (fig.1). Using the above chart (or manufacturer’s instructions ) as a guide determine if the material requires further thinning, if so then thin accordingly.  

喷枪适用于粘度范围在25~50秒能够流漏斗液体。记录下漏斗里液体流尽的时间，请参考上面的表格，记定此液体是否需要稀释，如果需要，那就需要做相应稀释。

If the paint requires thinning, start with a 10% dilution of the paint. To do this, fill a 1 liter container with the required paint. The viscosity cup supplied with the unit holds 1/10 of a liter, block the hole in the viscosity cup and fill up with the required thinner. Add the thinner to the paint and stir, measure the viscosity using the recommended viscosity chart above. If the paint requires further thinning, dilute the paint by another 5%(5% will be equal to half a viscosity cup)with the required thinner and measure the viscosity, if the paint is not at its recommended viscosity, repeat the above step.

如果需要稀释，先稀释稀释10%的量。这样先装满1L的需要喷涂的液体。漏斗可以装料桶1/10。堵住漏斗下面的洞，并装满稀释后的液体。把稀释剂加入涂料，并搅动。根据上述数据测量粘度。如果需果进一步稀释，冲淡涂料按5%（相当于漏斗的一半），重复上述步骤直至达到要求??

注意：有些漆不在上述范围内，欲知详情，请与我们联系。

 喷涂方式：

喷枪有三个不同的喷涂模式：水平，垂直，圆点

水平和垂直喷射用于大面积喷漆，圆点喷射用于小面积，比如角落，或者够不到的地方。

调整喷射模式的步骤：1、松开喷嘴固定圈，2、调整喷雾头的位置（参照图2）到水平，垂直或者圆点。3、重新拧紧喷嘴固定圈

涂料容量

喷漆量很容易调整（参照图3），顺时针方向将旋紧调节阀。按住扳手，逆时针旋转调节阀，直到你需要喷雾效果。如果喷射太宽或者想量更大，再顺时针调节，直至满意后再工作。

喷雾技法（图4）

 CLEANING INSTRUCTIONS清洗指示

THE SPRAY GUN MUST BE THOROUGHLY CLEANED IMMEDIATELY AFTER USE. IF THE PAINT DRIES INSIDE THE GUN, CLEANING WILL BECOME MUCH MORE DIFFICULT AND MAY RENDER THE GUN INOPERABLE. THIS IS NOT COVERED BY GUARANTEE.

喷枪使用后需?⒓辞逑础?如果涂料干在里边后再清洗将很困难，而且有可能导致喷枪不能工作。此不在保修范围内。

 清洗步骤

1??卸下料桶

2、将未用完的涂料倒入原桶中，以便下次使用。

3、倒入一定量的稀释液，轻轻摇晃，重新装好喷枪，将稀释液通过枪体喷出。重复以上步骤，直至稀释液全部喷出，

4、清洗喷枪外面的一些涂料

5、清洗料桶密封圈。